how to

How To Remove Fence Post With Concrete References

How To Remove Fence Post With Concrete. 5 break the pieces of concrete footing into smaller pieces with the digging. A wooden post that is sunk into the surrounding soil will be relatively easy to remove, while one that is sunk into concrete will require additional equipment.

how to remove fence post with concrete
Source : www.pinterest.com

After putting the 3 bags worth of concrete into the hole and ensuring it nicely surrounded the post, i used a small garden shovel to slope the concrete away from the fence post. Any wooden fence post that is severely deteriorated may also require additional tools to manage the extraction.step 2, dig a trench around the post using a shovel.

8 X 4 Concrete Fence Posts Concrete Fence Fence Post

Clear the area around the post and concrete footing. Depends on the post, the concrete footing and the soil.

How To Remove Fence Post With Concrete

Eventually, you should be able to lift the post out of the ground.First light tomorrow pour over boiling water.How to remove a fence post with concrete footing.I had half a dozen concrete posts that used to be part of a chain link fence between me and my neighbour.

I would use the same idea as the post in the concrete the same basic way you might half to cut the stump up in pieces or more you also might have a tap root to pull on if you can dig all the way around the stumpl first and make sure the stump is loose i used a 40 pound rebar to jam under the stumpl several different places and then stand on the end of it and jump up and down on the bar to loosen the stump you’ll get.If it stays in, you’ll need to try one of the following methods.If the post doesn’t easily lift out, you may need to dig deeper.If the post is not cemented, it should easily come out.

If you are due frost tonight then soak the concrete with cold water.In soft sand or muddy dirt, you can just start leaning against the post in alternating directions and it will often start moving.In these situations, it’s often easier to remove a few inches of dirt around the post’s base and then cut the post below grade with a reciprocating saw.Insert the spike tool fully into the ground at the edge of the concrete footing.

Instead of breaking up all the concrete around the post stub, just break off one side.It is not hard, keep digging so the hole you making is.Make sure it is not on top of the concrete that holds the stick.Move the back part back and forth to loosen it.

Next, lay a long piece of 4×4 over the hole and wrap a ratchet strap around it and around the sides of the block.Not around it, just on one side.Only other thing i can think of is to plum the post and then add postcrete to hold it.Place a concrete block on the ground about 6 inches from one side of the stick.

Pull the fence post straight up.Remove anything attached to the post, such as railings or old nails/screws.Repeat step 2 at equal spaces around the concrete footing.Rock the post back and forth to loosen it using your body weight or a sledgehammer.

Screw lag bolts through a chain into the broken off fence post and then use a vehicle winch/come along/high lift jack to pull the post out.Step 1, assess the status of the fence post.That should produce cracks that more easily split when hit with a hammer.That would have made it easy to remove the post remnant and left a channel for the new post.

The idea it to make a little ramp so water flows away from the wooden post on all 4 sides.The trench does not have to be any deeper than about 1 foot (0.3 m).There are a lot of methods to tear out fence posts with concrete, but it really comes down to what tools you have available to get the job done.To get around this, wherever possible, shift the fence post layout such that you can dig new holes.

To remove a broken fence post set in concrete, first, dig the concrete block out with a shovel.Turn on water flow to the wood post puller.Unfortunately, when such a fence post is broken off at ground level, removing the concrete or cement base by bolting a strong piece of wood to the fence post and using it as leverage isn’t possible.Use the digging bar as a lever to pry the concrete away from the base of the post and lift the post out of the footing.

Work at it a bit and the post will lift right out with the co.Wrap a chain around the post and use a high lift jack to pull the post out.You’ll also want to pull the chain so it sits snug around the concrete.