how to

How To Make A Valance Board References

How To Make A Valance Board. 12″ was allowed for the center pleat. 13 board mounted valance ideas (with pictures) board mounts are the best way to ensure that a window treatment hangs properly.

how to make a valance board
Source : www.pinterest.com

Box pleat valances are usually mounted to a board, but you can make a box pleat valance on a rod, too and it’s super easy. Cornice boards are cheap to make.

15 DIY Window Treatments Valance Patterns Window

Cut poster board into one 48” x 10” piece and two 8” x 10” pieces. Decide how long you want it and how wide.

How To Make A Valance Board

Fold fabric
over on every side and hem with fusible web, making sure iron is set to no steam.
Fold over the fabric and mark the center of the fabric.Fold right toile section at the 23.5″ wide to begin center pleat.Follow my step by step tutorial with pictures.

For the height but i think anywhere from 5.For the width measure how far the drape extends out and go beyond that by about 2”.Here’s how to make a board mounted window valance.I bought a pre primed piece of mdf wood and had it cut down to 65” x 11”.

I finally decided i wanted to make a wooden cornice.I have been staring at the blank window in my living room for a whole year now.I kept thinking about doing a window valance tutorial and then kept putting it off.I make this with a custom pattern and i will show you how to make one too.

I wanted a fairly large cornice so i chose 11 in.I will show you my process for making this pretty treatment.In addition, extend the width of the valance box approximately 10″ on either side of the window.Leave about 1/8” of space from the wall.

Line up the marked edge with the top of the window, then draw a line just above the paint stick.Make sure the valance board is centered.Mark two spots above every window for the l brackets.Measure 23.5″ from the right side of the toile section to center of valance.

Measure and mark the center of the board as well.Measure from top of window frame down to where you want the valance to hang.Measure the window from side to side to get the width of the valance, and measure from the curtain rod to the part of the window where you want the valance to end to get the length of your.Measure your window and decide what your measurements will be.

Next, cut two pieces of foam and place/glue over the back seam where the two boards meet to act as braces.No visible rod pocket stitches and no constant adjustments on the curtain rod needed.Now cut two pieces that are 3 inches wide to serve as the sides of your valance.Once cut, attach them to your long piece of foam by using a few finish nails per side and just pushing in.

Repeat with left side toile section.Screw the valance board on the wall.See more ideas about custom window treatments, window treatments, window coverings.The distance of the valance board from the top of the window frame should be roughly two.

The easiest way was to measure 5 inches and mark it on a paint stick.The rest of the valance will be made the same way as in the tutorial.The top flat part of the l bracket sat at the marked line on the wall.Then measure and mark half that on both the fabric and the board to get to the center of where the.

There are lots of variables thrown into this calculation, so your exact cost may vary quite a bit from mine depending on your materials (how expensive the fabric you choose is, and what type of wood you use, etc).This fold will be approximately 3″ deep on each side and 6″ along back of pleat.Time to measure for placement on the valance board.To even out our asymmetrical windows, i extended the window box valance 6″ on the left, and 10″ on the right and pull the curtains across the windows so it looks like it is evenly spaced.

To get started, cut your foam to the desired length (outside casing to outside casing) using a serrated knife.To make this you’ll need to start out with a long piece of mdf wood.Trim fabric to vertical and horizontal lengths, leaving one extra inch on the top, bottom and sides.Use hot glue to attach.

Whether you sew or you don’t, you can get a custom look, it’s really all about the ironing!With the “right” side of your window valance facing up (the side with the tape on the seams), apply the peel and stick wallpaper to the foam board, letting the edges hang over and smoothing out bubbles with a paper scraper.Work carefully across the full.You can make the pattern to any length, width or depth, depending upon the dimensions of your.

You can save hundreds of dollars if you do.