How To Drain Sprinkler System Backflow References

How To Drain Sprinkler System Backflow. (usually located in the basement or crawl space) step 2: A sprinkler system can stop working for many reasons.

how to drain sprinkler system backflow
Source : www.pinterest.com

Adjust all ball valves and backflow test cocks to a 45 degree angle. All you have to do is turn off the water at the water main, clean the valve and reattach it to the lines.

100DVFSS 1 In DVF Series Inline Plastic Residential

Allow all of the water to drain from the sprinkler heads. Backflow creates the potential for fertilizers, herbicides and other unwanted harmful substances to move from an irrigation system and into the public or potable water supply.

How To Drain Sprinkler System Backflow

Go to the controller and turn on an irrigation or sprinkler zone.If the system has a pump, it should be drained, removed from the system and stored inside.If this is not possible, drain the pump and wrap it to insulate it from the weather.If you find that the irrigation controller isn’t the culprit, check the city water meter to make sure you have a water supply to the backflow.

If your irrigation system is attached to domestic water, it is required to have a backflow prevention device.Install the 1/4″ quick disconnect fitting into one of the test cocks on the backflow preventer.It is tagged as “drain valve“.Leave them open for a few days, if possible.

Make sure to have a bucket available for.Make sure you do this to all 4 ball valves.Manual drain valve locate the manual drain valves situated downstream of each zone valve.Most of the time it’s something very simple like the irrigation controller is turned off or has lost its programming due to a power loss or surge.

Not only must they be licensed and file the proper permits and provide the mandatory backflow preventer performance test forms but they may unintentionally create a cross connection that could be potentially dangerous or even lethal.Once it has been attached test the sprinkler system for at least 10 minutes to make sure it is no longer leaking.Open all the manual drain valves for each zone in the system, and leave them open so that all the water drains from the pipes and sprinkler heads.Open all the manual drain valves for each zone in the system, and leave them open so that all the water drains from the pipes and sprinkler heads.

Open each of the valves in the pipes to release the water pressure.Open the 2 petcock’s (f) with a flat head screwdriver so that the screw head runs a 45 degree angle.Open the inside drain (b) to drain your system.Over 25 years of professional, licensed installation experience.

Power up your sprinkler system, and then shut it off—you should see the auto valve drain once the pressure is off.Referencing the diagram below, follow these instruction to perform a quick drain of your system:Related posts about backflow preventers.Shut off sprinkler water supply valve (1) by turning to the right.

Shut off valve in the normal operating position (on).Shut off valve in the “off” position.Steps how to drain your sprinkler / irrigation system:Thanks to its drainage hole, you can drain any remaining water in the pipe after you are done, and this will help to prevent further contamination.

The basics of draining a sprinkler system for the winter.The diy lawn sprinkler installer, the landscaper or a handyman is not properly trained or licensed to test the proper backflow preventer that will protect your home and family.The drain for your system may be located outside near the backflow or may be in your basement.This allows the water inside the backflow to drain from the unit.

This backflow pressure preventer is meant to work on portable water lines, and its assembly should help in giving protection when any potential hazards come up due to water contamination.This leaves water remaining from the inside of the backflow preventer all the way to the main valve underground.This will ensure you turned the water off correctly and drain the pressure from the system.To blow out the system:

Turn both test ports (5) to 45 degrees.Turn off the water supply by closing the main valve to the sprinkler system.Turn off your water at the dedicated sprinkler line shutoff (a) in your basement / crawlspace.Turn on one of your irrigation system zones (and leave it on).

Turn the water off to your sprinkler system.Turn this off and open up the inlet drain valve, which will be located between the.Using a small screwdriver, pull up the backflow preventer’s stopper so it’s touching the top of the casing (open).Usually in your basement or crawl space.

We offer dallas sprinkler system and irrigation system installations that use only high quality lawn sprinkler, drip irrigation, drainage, french drain and landscape.When the water draining from the device subsides, give the device a few light shakes to get a little more water out of the device.When this happens it can be fixed just like fixing a normal valve!When you blow out your sprinkler system, you typically blow air from the front side of your backflow preventer into the network of sprinkler pipe.

Leave a Reply

Your email address will not be published. Required fields are marked *